British Columbia · Energy · checked September 28, 2026

Heat loss calculations in Richmond

The heat loss calculation is how a heat pump or furnace gets sized for your house, and the key input is the design temperature: −4.4°C for Richmond, from NRCan's HOT2000 climate data for Vancouver International.

Get matched in Richmond → The CSA F280 heat-loss calculation
A kitchen table with a house floor plan, a laser measure, a tape measure and a laptop showing the plan

Design temperature

−4.4°C

Heating degree-days

2,768

Standard

CSA F280

Typical cost

$150–$400 standalone

How Richmond is built

Richmond's houses by when they were built Ten house shapes, one for each tenth of Richmond's 46,950 houses. Before 1961: 5%, 1961–1990: 45%, 1991–2000: 21%, 2001 or later: 31%. Older houses glow hotter.
  • Before 1961 5%
  • 1961–1990 45%
  • 1991–2000 21%
  • 2001 or later 31%
Each house stands for one in ten of Richmond's 46,950 houses (single-detached, semi-detached, row and duplex), drawn by when it was built. The glow shows the usual pattern: older houses tend to be leakier and less insulated. Snowfall scales with heating degree-days. Sources: Statistics Canada 2021 Census (table 98-10-0233-01), NRCan HOT2000 climate data.

Why the design temperature matters in Richmond

−4.4°C is the 5th-mildest design temperature of the 70 cities we cover. The F280 calculation works out how much heat each room loses on that design day, from the house's actual walls, windows, air leakage and ceiling insulation.

With a design day that mild, a heat pump sized to the calculation can carry most or all of a typical Richmond house's heating load, which makes sizing it right, rather than oversizing it, the main job.

In the Vancouver area, 32% of households heat mainly with a forced-air furnace, 31% with electric baseboards, 12% with a boiler and radiators and 5% with a heat pump; natural gas is the main heating energy for 42% of households and electricity for 39% (Statistics Canada, 2023).

Why skipping it costs money

Contractors who size by square footage routinely oversize. An oversized heat pump costs more to buy, cycles on and off, dehumidifies poorly in summer and wears faster. An undersized one leans on backup heat. The F280 report is the evidence either way, and it's worth having before you compare quotes.

What it costs

About $150–$400 as a standalone calculation (a September 2026 planning range; quotes vary). Many energy advisors bundle it with an EnerGuide evaluation, which also gives the calculation measured air-leakage data instead of an assumption.

NRCan-licensed service organizations serving Richmond

Many energy advisors also do room-by-room CSA F280 calculations for an extra fee; HVAC designers do them too. Ask for the F280 report itself, not just an equipment recommendation.

Source: NRCan list of licensed service organizations, checked September 28, 2026. Call to confirm your street is covered and ask about wait times.

Heat pump programs in Richmond

Provincial · needs an evaluation BC Home Energy Improvement Bonus $20 for every percentage-point your home improves — $750 minimum, $2,000 maximum — or $300 for any two upgrades Open Provincial CleanBC Energy Savings Program Free energy-saving upgrades for income-qualified BC households — insulation, heat pumps and more, installed at no cost Open · deadline Federal CMHC Eco Improvement premium refund 25% back on your CMHC mortgage insurance premium after $20,000 of energy renovations Open Federal Canada Greener Homes Affordability Program Free retrofits for low-to-median-income households in BC, Manitoba, Nova Scotia, PEI and Quebec — not available in Ontario Open · deadline Municipal City of Richmond residential heat pump rebate and electrical upgrade top-up City page: owners of single-family homes, duplexes and townhomes get a $350 City rebate on top of CleanBC rebates when switching from oil, natural gas or propane to an electric heat pump, plus up to $500 more for a needed electrical system upgrade. The page was last published Sept 2024; the City's heat pump story map (updated Aug 2026) still says incentives and electrical-upgrade top-ups are available but gives no amounts. Treat 2026 availability and amounts as unconfirmed.

Heat loss calculation in Richmond: common questions

What design temperature is used for heat pump sizing in Richmond?

NRCan's HOT2000 climate data gives −4.4°C for Vancouver International. Your designer may use the building code's design value for Richmond, which can differ slightly; ask which one the calculation uses.

How much does a heat loss calculation cost?

About $150–$400 standalone as a planning range; often less when bundled with an EnerGuide evaluation.

Who does F280 calculations in Richmond?

Many of the 27 NRCan-licensed organizations serving Richmond offer them, as do HVAC designers. Ask for the F280 report itself.

Do rebate programs require a heat loss calculation?

Requirements vary by program and change often. Even where it isn't required, it is the best protection against an oversized or undersized system.

Heat loss calculation near Richmond

Heat loss calculation in Vancouver11 kmHeat loss calculation in Delta11 kmHeat loss calculation in Burnaby14 kmHeat loss calculation in Coquitlam21 kmHeat loss calculation in Surrey22 km All 70 cities →

Sources

Checked September 28, 2026. Census figures are for the municipality (British Columbia); climate data is NRCan's HOT2000 station Vancouver International (5 km away).

Get matched with a registered advisor in Richmond

Tell us your postal code and what you’re planning. We’ll connect you with one licensed service organization serving your area. No spam, no shared lead lists.

Email us what you’re planning, your postal code and the type of building (a house, a duplex or triplex, or a larger multi-unit building) — we’ll reply with registered service organizations for your area and which rebates apply.

Email dave@clickshift.ca

This inbox is answered by a person. Participating advisors pay us a referral fee — you pay nothing, and it never affects the directory.