Ontario · Energy · checked September 28, 2026

Heat loss calculations in Windsor

The heat loss calculation is how a heat pump or furnace gets sized for your house, and the key input is the design temperature: −15.2°C for Windsor, from NRCan's HOT2000 climate data for Windsor.

Get matched in Windsor → The CSA F280 heat-loss calculation
A kitchen table with a house floor plan, a laser measure, a tape measure and a laptop showing the plan

Design temperature

−15.2°C

Heating degree-days

3,306

Standard

CSA F280

Typical cost

$150–$400 standalone

How Windsor is built

Windsor's houses by when they were built Ten house shapes, one for each tenth of Windsor's 71,290 houses. Before 1961: 43%, 1961–1990: 30%, 1991–2000: 12%, 2001 or later: 15%. Older houses glow hotter.
  • Before 1961 43%
  • 1961–1990 30%
  • 1991–2000 12%
  • 2001 or later 15%
Each house stands for one in ten of Windsor's 71,290 houses (single-detached, semi-detached, row and duplex), drawn by when it was built. The glow shows the usual pattern: older houses tend to be leakier and less insulated. Snowfall scales with heating degree-days. Sources: Statistics Canada 2021 Census (table 98-10-0233-01), NRCan HOT2000 climate data.

Why the design temperature matters in Windsor

−15.2°C is the 15th-mildest design temperature of the 70 cities we cover. The F280 calculation works out how much heat each room loses on that design day, from the house's actual walls, windows, air leakage and ceiling insulation.

At −15.2°C, a cold-climate heat pump sized to the calculation can carry most of the season, and the number shows how much backup heat the coldest days need.

In the Windsor area, 78% of households heat mainly with a forced-air furnace; natural gas is the main heating energy for 67% of households and electricity for about 21% (Statistics Canada, 2023).

Why skipping it costs money

Contractors who size by square footage routinely oversize. An oversized heat pump costs more to buy, cycles on and off, dehumidifies poorly in summer and wears faster. An undersized one leans on backup heat. The F280 report is the evidence either way, and it's worth having before you compare quotes.

What it costs

About $150–$400 as a standalone calculation (a September 2026 planning range; quotes vary). Many energy advisors bundle it with an EnerGuide evaluation, which also gives the calculation measured air-leakage data instead of an assumption.

NRCan-licensed service organizations serving Windsor

Many energy advisors also do room-by-room CSA F280 calculations for an extra fee; HVAC designers do them too. Ask for the F280 report itself, not just an equipment recommendation.

Only assessments from the seven HRSP-approved organizations qualify for the $600 Home Renovation Savings rebate and its assessment-path upgrade rebates; each listing below says whether it's one of them.

Source: NRCan list of licensed service organizations, checked September 28, 2026. Call to confirm your street is covered and ask about wait times.

Heat pump programs in Windsor

Provincial · needs an evaluation Home Renovation Savings — Home Energy Assessment path Up to $10,000 per home for insulation, windows and air sealing, plus $600 back on your assessments — if the follow-up assessment is done by December 31, 2026 Open · deadline Provincial Home Renovation Savings — direct rebates (no assessment) Heat pumps up to $7,500 ($12,000 ground-source), solar with battery up to $10,000, plus attic, thermostat and appliance rebates — no assessment needed Open Federal CMHC Eco Improvement premium refund 25% back on your CMHC mortgage insurance premium after $20,000 of energy renovations Open

Heat loss calculation in Windsor: common questions

What design temperature is used for heat pump sizing in Windsor?

NRCan's HOT2000 climate data gives −15.2°C for Windsor. Your designer may use the building code's design value for Windsor, which can differ slightly; ask which one the calculation uses.

How much does a heat loss calculation cost?

About $150–$400 standalone as a planning range; often less when bundled with an EnerGuide evaluation.

Who does F280 calculations in Windsor?

Many of the 19 NRCan-licensed organizations serving Windsor offer them, as do HVAC designers. Ask for the F280 report itself.

Do rebate programs require a heat loss calculation?

Requirements vary by program and change often. Even where it isn't required, it is the best protection against an oversized or undersized system.

Heat loss calculation near Windsor

Heat loss calculation in Chatham-Kent66 kmHeat loss calculation in London162 kmHeat loss calculation in Waterloo238 kmHeat loss calculation in Kitchener241 kmHeat loss calculation in Brantford242 km All 70 cities →

Sources

Checked September 28, 2026. Census figures are for the municipality (Ontario); climate data is NRCan's HOT2000 station Windsor (3 km away).

Get matched with a registered advisor in Windsor

Tell us your postal code and what you’re planning. We’ll connect you with one licensed service organization serving your area. No spam, no shared lead lists.

Email us what you’re planning, your postal code and the type of building (a house, a duplex or triplex, or a larger multi-unit building) — we’ll reply with registered service organizations for your area and which rebates apply.

Email dave@clickshift.ca

This inbox is answered by a person. Participating advisors pay us a referral fee — you pay nothing, and it never affects the directory.